PT. SAVONT
VARAVI INDONESIA
“AUTHORIZED
DISTRIBUTOR OF PHILIPS LIGHTING INDONESIA”
Ruko Serua Indah Residence, Jln. Serua Raya no. 6-7 Reni Jaya - Bojongsari - Depok , Jawa Barat 16517
Telp : 021- 7419460/021-7494545 Fax : 021- 7419460
Contact Person : Tommy Bhong (08.11111.0694 / 0815.160.6771 / 0859.3976.3399)
Whatsapp : 08.11111.0694, BBM : D25E877F Skype : tommy.bhong2
Email : sales_support@savontindonesia.com Website :http://www.savont-indonesia.net/
STEPLIGHT (LAMPU TANGGA) Square Ramp 6051 1,4W 3000K
Could very well cast into walls or walls both indoors and outdoors. Ideally suited as an
orientation to the floor / ground. Very good shielding and glare-free light. The
performance is top quality with front in powder coated aluminum to remain beautiful for
many years, under all conditions. The house is also in aluminum. All bolts and gaskets in
the best quality. LED module is from the renowned German supplier Vossloh Schwabe.
Recommended mounting height: 25 - 50cm from the floor / ground.n eed external driver
/ transformer type 350mA DC to light (not included). Sleeve box included if it is to be
embedded. Attaches to the hole edge with suitable structural adhesive. The light
source can not be replaced, but will normally have a lifespan of over 15 years if it is on
average 6 hours. day.
Specifications
Fixture is manufactured in compliance with international standard of general
requirement IEC 60598-1, fixed general purpose luminaires IEC 60598-2-1
and recessed luminaires IEC 60598-2-2. Electrical protection class3.
Protection against dust and water Ip55. Protection against mechanical impact
IK07 on body and optical part.
Luminaire body housing made of high-pressure die cast aluminium alloy. Wall
installation block out in Polypropylene. Corrosion resistance and suitable for
outdoor use.
Nano Ceramic surface coversion, resistant to corrosive environment.
Luminiare primarily coated with epoxy resin and top coated with UV
stabilized polyester powder and cured in digital temperature controlled
chamber at 200°C.
Impact resistant frosted safety tempered glass diffuser.
Molded silicone gasket. Temperature and weather resistant. Working
temperature -40°C to +200°C.
External screws in 316 stainless steel with silicone grease dipping.
Cable entry protected by weather proof PG9 silicone grommet. Prepare for
H05RN-F / H07RN-F cable diameter 6 – 8mm.
G4 lampholder for QT9 lamp in PPS body with nickel-coated contact from
Vossloh Schwabe – Germany. ENEC approved.
Terminal block in PA6.6 nickel plated brass insert 600V/24A – VDE approved.
Working temperature -40°C to +130°C. For cable with 1.5mm. cross section.
Telp : 021- 7419460/021-7494545 Fax : 021- 7419460
Could very well cast into walls or walls both indoors and outdoors. Ideally suited as an
orientation to the floor / ground. Very good shielding and glare-free light. The
performance is top quality with front in powder coated aluminum to remain beautiful for
many years, under all conditions. The house is also in aluminum. All bolts and gaskets in
the best quality. LED module is from the renowned German supplier Vossloh Schwabe.
Recommended mounting height: 25 - 50cm from the floor / ground.n eed external driver
/ transformer type 350mA DC to light (not included). Sleeve box included if it is to be
embedded. Attaches to the hole edge with suitable structural adhesive. The light
source can not be replaced, but will normally have a lifespan of over 15 years if it is on
average 6 hours. day.
Specifications
Fixture is manufactured in compliance with international standard of general
requirement IEC 60598-1, fixed general purpose luminaires IEC 60598-2-1
and recessed luminaires IEC 60598-2-2. Electrical protection class3.
Protection against dust and water Ip55. Protection against mechanical impact
IK07 on body and optical part.
Luminaire body housing made of high-pressure die cast aluminium alloy. Wall
installation block out in Polypropylene. Corrosion resistance and suitable for
outdoor use.
Nano Ceramic surface coversion, resistant to corrosive environment.
Luminiare primarily coated with epoxy resin and top coated with UV
stabilized polyester powder and cured in digital temperature controlled
chamber at 200°C.
Impact resistant frosted safety tempered glass diffuser.
Molded silicone gasket. Temperature and weather resistant. Working
temperature -40°C to +200°C.
External screws in 316 stainless steel with silicone grease dipping.
Cable entry protected by weather proof PG9 silicone grommet. Prepare for
H05RN-F / H07RN-F cable diameter 6 – 8mm.
G4 lampholder for QT9 lamp in PPS body with nickel-coated contact from
Vossloh Schwabe – Germany. ENEC approved.
Terminal block in PA6.6 nickel plated brass insert 600V/24A – VDE approved.
Working temperature -40°C to +130°C. For cable with 1.5mm. cross section.